Belkin - G Plus MIMO F5D9231-4 v1 (Belkin Firmware)


Port Forwarding Guide
For automatic port forwarding try Simple Port Forwarding

Step 1.

Some routers & modems work best with port forwarding if you have a static local IP.
Manually set your network interface card ( NIC ) to use a static ip address.
You can also download my FREE Simple Static IP tool to set it for you.

Step 2.

Open your favorite web browser and input your routers ip address in the address bar.
Please note that you must have the http:// in order to connect to your router/modem properly.

Need help finding you router IP address? Click here

Step 3.

Some router/modems require a username and/or password, if yours requires it, enter the routers username and password here.

If you don't know it you can check our list of default router and modem password list here.

If you have changed it and don't remember it you may have to reset your device to factory default using the reset button on most routers.

Step 4.

Once logged into your router click on "Virtual Servers".

Click To View Full Picture

Step 5.

On 'Enable' make sure to check mark it.

Under 'Description' Give your entry a name, it must not be the same as any others on this page.

In 'Inbound port' & 'Private port' enter the ports to be forwarded.
Example: 2100 to 2200 or 3000 to 3000

For 'Type' select the protocol for the ports.

In the 'Private IP Address' field put the local IP of the computer the ports will be forwarded to.

Repeat this step for all ports.

Click To View Full Picture

Step 6.

Click 'Apply Changes' once all ports have been entered.

All done!

Belkin - F5D7230-4 v9 (Belkin Firmware)


Port Forwarding Guide
For automatic port forwarding try Simple Port Forwarding

Step 1.

Some routers & modems work best with port forwarding if you have a static local IP.
Manually set your network interface card ( NIC ) to use a static ip address.
You can also download my FREE Simple Static IP tool to set it for you.

Step 2.

Open your favorite web browser and input your routers ip address in the address bar.
Please note that you must have the http:// in order to connect to your router/modem properly.

Need help finding you router IP address? Click here

Step 3.

Some router/modems require a username and/or password, if yours requires it, enter the routers username and password here.

If you don't know it you can check our list of default router and modem password list here.

If you have changed it and don't remember it you may have to reset your device to factory default using the reset button on most routers.

Step 4.

Once logged into your router click on "Virtual Servers".

Click To View Full Picture

Step 5.

On 'Enable' make sure to check mark it.

Under 'Description' Give your entry a name, it must not be the same as any others on this page.

In 'Inbound port' & 'Private port' enter the ports to be forwarded.
Example: 2100 to 2200 or 3000 to 3000

For 'Type' select the protocol for the ports.

In the 'Private IP Address' field put the local IP of the computer the ports will be forwarded to.

Repeat this step for all ports.

Click To View Full Picture

Step 6.

Click 'Apply Changes' once all ports have been entered.

All done!

Linksys - RT31P2 (Linksys Firmware)


Port Forwarding Guide
For automatic port forwarding try Simple Port Forwarding

Step 1.

Some routers & modems work best with port forwarding if you have a static local IP.
Manually set your network interface card ( NIC ) to use a static ip address.
You can also download my FREE Simple Static IP tool to set it for you.

Step 2.

Open your favorite web browser and input your routers ip address in the address bar.
Please note that you must have the http:// in order to connect to your router/modem properly.

Need help finding you router IP address? Click here

Step 3.

Some router/modems require a username and/or password, if yours requires it, enter the routers username and password here.

If you don't know it you can check our list of default router and modem password list here.

If you have changed it and don't remember it you may have to reset your device to factory default using the reset button on most routers.

Step 4.

Once logged into your router click on the "Applications & Gaming" tab.

Click To View Full Picture

Step 5.

Normally 'Port Range Forward' is chosen by default, if not click it.

Under 'Application' Give your entry a name, it must not be the same as any others on this page.

In 'Start' & 'End' enter the ports to be forwarded.
Example: 2100 to 2200 or 3000 to 3000

Next select the protocol for the ports.

In the 'IP Address' field put the local IP of the computer the ports will be forwarded to.

On 'Enable' make sure to check mark it.

Repeat this step for all ports.

Click To View Full Picture

Step 6.

Click 'Save Settings'

All done!

Linksys - WRT300N (Linksys Firmware)


Wireless Setup Guide

Note: When setting up or changing your wireless settings it is a good idea to be plugged into the router with your network cable and not your wireless connection.
          If you are using your wireless connection and make any changes you will lose you wireless connection.

Step 1.

Open your favorite web browser and input your routers ip address in the address bar.
Please note that you must have the http:// in order to connect to your router/modem properly.

Need help finding you router IP address? Click here

Step 2.

Some router/modems require a username and/or password, if yours requires it, enter the routers username and password here.

If you don't know it you can check our list of default router and modem password list here.

If you have changed it and don't remember it you may have to reset your device to factory default using the reset button on most routers.

Step 3.

Once logged into your router click on the "Wireless" tab.

Click To View Full Picture

Step 4.

By default 'Basic Wireless Setting' should be chosen, if not click it now.

For 'Wireless Network Mode' set to enable.

For 'Wireless Network Name (SSID)' set a name you would like to call your wireless.
What you put here is what will show up when you are searching for a wireless connection.

For 'Wireless SSID Broadcast' normally you will have this set to enable.
This will broadcast your wireless connection to be detected by your wireless card.
This is a good way for a standard user to find the network, but also why it is important to have wireless security in place.

Once all information is set click on 'Save Settings'

Click To View Full Picture

Step 5.

Now click on 'Wireless Security'

For 'Security Mode:' you will have multiple options, for the sake of keeping this guide simple I recommend you choose WPA.
WPA is widely supported by wireless cards and allows you to set your own password.

Once you have your security set more boxes will appear on screen.

For setting your wireless password you will enter it into the 'Passphrase' or 'Password' box.

Once you have your setting all set click 'Save Settings'

Click To View Full Picture

All done!

Linksys - WRT300N (Linksys Firmware)


Port Forwarding Guide
For automatic port forwarding try Simple Port Forwarding

Step 1.

Some routers & modems work best with port forwarding if you have a static local IP.
Manually set your network interface card ( NIC ) to use a static ip address.
You can also download my FREE Simple Static IP tool to set it for you.

Step 2.

Open your favorite web browser and input your routers ip address in the address bar.
Please note that you must have the http:// in order to connect to your router/modem properly.

Need help finding you router IP address? Click here

Step 3.

Some router/modems require a username and/or password, if yours requires it, enter the routers username and password here.

If you don't know it you can check our list of default router and modem password list here.

If you have changed it and don't remember it you may have to reset your device to factory default using the reset button on most routers.

Step 4.

Once logged into your router click on the "Applications & Gaming" tab.

Click To View Full Picture

Step 5.

Click 'Port Range Forwarding'

Under 'Application Name' Give your entry a name, it must not be the same as any others on this page.

In 'Start ~ End Port' enter the ports to be forwarded.
Example: 2100 to 2200 or 3000 to 3000

Next select the protocol for the ports.

In the 'IP Address' field put the local IP of the computer the ports will be forwarded to.

On 'Enable' make sure to check mark it.

Repeat this step for all ports.

Click To View Full Picture

Step 6.

Click 'Save Settings'

All done!